For most of its history, Portland treated air conditioning as optional. Summers were mild, nights cooled off, and plenty of older homes were built with a gas furnace and nothing else. Then June 2021 arrived, and the temperature at Portland International Airport climbed to 108, then 112, then an all-time record of 116 degrees over three straight days.
Adding cooling to a house that was never designed for it is a different job from replacing an existing AC. The ductwork, the electrical panel, and the filter setup all have to be checked before anyone picks equipment. That’s why a good HVAC contractor in Portland, OR will usually start with the house itself rather than a product brochure, since the right system depends on what’s already behind the walls.
An outdoor heat pump unit beside an older Craftsman-style home with tall evergreens behind it.

Why Portland Homes Are Rethinking Cooling
The heat dome wasn’t just a hot week. It broke the assumption that a Portland home could ride out summer with fans and open windows. Two things make that assumption shakier now than it used to be.

Hot nights are the real problem
Daytime highs grab the headlines, but it’s the nights that decide whether a house can recover. During the 2021 event, Portland set a new record warm overnight low of 75 degrees, according to the same KOIN report. When the outdoor air never cools down, opening windows at night stops working as a cooling strategy.
Smoke season overlaps heat season
Wildfire smoke tends to arrive in late summer, right when homes need cooling most. Closing every window to keep smoke out turns a house into an oven without some form of mechanical cooling. A system that can cool and filter at the same time solves both problems at once.
Your Options for Adding Cooling
There’s no single right answer, and the best choice depends heavily on whether the home already has ducts. Here’s how the main options compare.
| Option | Uses Existing Ducts | Also Heats | Whole-Home Filtration | Best Fit |
|---|---|---|---|---|
| Central AC added to a gas furnace | Yes | No, furnace still heats | Yes, through the furnace filter | Homes with good ducts and a newer furnace |
| Ducted heat pump | Yes | Yes | Yes | Homes with ducts ready for a full system upgrade |
| Ductless mini split | No | Yes | Limited, filters at each indoor head | Homes with no ducts or with rooms ducts don’t reach |
| Window or portable units | No | Usually no | Minimal | Renters and short-term stopgaps |
Window units got a lot of Portland households through 2021, and there’s no shame in that. They’re just a stopgap, since they cool one room, offer little filtration, and block a window that might otherwise stay sealed during smoke events.
Why heat pumps fit Portland so well
A heat pump is an air conditioner that can also run in reverse to heat the house. Portland’s winters are mild enough that a modern heat pump handles most heating days comfortably. For many older homes, that means one system can provide summer cooling and do most of the winter heating, sometimes with the existing furnace kept as backup for the coldest stretches.
If your home has no ductwork at all, ductless mini splits are usually the cleaner route. They avoid tearing open walls and ceilings to add ducts, and each indoor unit controls its own zone.
Check the Ductwork Before You Buy Equipment

Ducts installed for a furnace weren’t necessarily sized for cooling. Cool air is denser and typically needs more airflow than heating, so undersized ducts can leave a new AC noisy, inefficient, and unable to reach upstairs rooms. A good assessment looks at the following before recommending equipment:
- Duct sizing. Are supply and return ducts large enough to carry the airflow cooling requires?
- Leaks and disconnected runs. Older ducts in attics and crawlspaces often leak, which wastes cooled air into spaces you don’t live in.
- Insulation. Uninsulated ducts running through a hot attic lose much of their cooling before air reaches the vents.
- Return air. Many older homes have a single return, which can starve a cooling system and leave closed-off rooms stuffy.
- Filter slot. A thin one-inch filter slot limits your options for smoke filtration, so it’s worth checking now.
Fixing ducts is rarely glamorous, but it often matters more than the brand of equipment. A well-sized system on leaky, undersized ducts will still feel like a bad system.
Filtration for Smoke Season

Once a home has central air or a ducted heat pump, the filter becomes your first line of defense against smoke. The EPA’s guidance on indoor air filtration during wildfire smoke recommends higher efficiency filters, with MERV 13 or higher especially effective at capturing fine smoke particles. Most homes still run a basic fiberglass filter that does very little for smoke.
Make sure your system can handle a better filter
Higher efficiency filters create more resistance to airflow, especially in a thin one-inch format. A thicker media filter cabinet, often four or five inches deep, gives you better filtration with less strain on the blower. We cover what these filters actually capture in our explainer on what MERV 13 protects against.
Run the fan during smoke events
Filtration only works when air is moving through the filter. During smoky days, running the system fan continuously keeps indoor air cycling through it even when the house doesn’t need cooling. Keep windows closed and check the filter more often, since smoke loads filters faster than normal household dust.
Electrical Capacity and Sizing

Older homes sometimes have electrical panels that weren’t built with central cooling or a heat pump in mind. Adding a large new electrical load may require a panel upgrade or a new dedicated circuit. It’s better to find that out during the quote than on installation day.
Sizing matters just as much. A system that’s too large cools quickly but cycles on and off, which wastes energy and wears components faster. A proper load calculation looks at the home’s insulation, windows, orientation, and air leakage rather than just square footage, and our guide to choosing the right AC unit for your climate explains why rules of thumb often miss.
Once the new system is running, routine care keeps it that way. Our breakdown of why small AC problems turn into expensive repairs covers the early warning signs worth catching.
Frequently Asked Questions
Can you add central air to a house with a gas furnace?
Usually, yes. If the home has ductwork, an air conditioner or heat pump can often be added alongside the existing furnace, sharing its blower and ducts. The ducts should be checked first, because ducts sized for heating are sometimes too small for the airflow cooling needs.
Is a heat pump a good choice for Portland?
For many homes it is. Portland’s mild winters suit modern heat pumps well, which means a single system can handle summer cooling and most winter heating. Some homeowners keep an existing gas furnace as a backup for the coldest days.
What if my house has no ductwork?
Ductless mini splits are usually the most practical option for homes without ducts. Each indoor unit cools and heats its own zone and connects to an outdoor unit through a small line set. They avoid the cost and disruption of adding new ductwork through finished walls and ceilings.
What filter should I use for wildfire smoke?
The EPA recommends higher efficiency filters for smoke, with MERV 13 or higher being especially effective for fine particles. Check that your system can handle the extra airflow resistance, ideally with a thicker media filter cabinet. Run the system fan continuously on smoky days and replace the filter more often.
Do I need an electrical panel upgrade to add a heat pump?
Not always, but older homes sometimes do. A heat pump or central AC adds a significant electrical load and usually needs a dedicated circuit. An installer should review your panel’s capacity as part of the quote so there are no surprises on installation day.
Wrapping Up
Portland’s summers have changed, and plenty of homes are still built for the old version. The good news is that adding cooling doesn’t have to mean a wall of window units or ripping the house apart. It means starting with the ducts, the panel, and the filter slot, then choosing equipment that fits what’s already there.
Done right, the same upgrade covers three problems at once. It keeps the house livable through the next heat wave, filters smoke out during fire season, and often lowers heating costs through the winter.

